DSM FP3065 Ball Bearing Turbocharger	Back

		Customer Rating: Not yet rated Quantity in Basket: None Shipping Weight: 20.00 pounds Price: $1,520.00 Options: 90 Degree Elbow: None Driver-side outlet - [add $95] Pass-side outlet - [add $95] Quantity:

Introduction

It took a long time for the evolution of DSM powerplants to get to the point where 550-650 HP turbochargers were even needed. In the beginning, Mitsubishi Heavy Industries said "Let there be 16g's" and there were, and it was good. Later, 20g and larger Mitsu-Garrett hybrids such as the FPGreen and FPRed ruled the land. They offered additional airflow capacity while still bolting on to the original manifolds, oxygen sensor housings and oil/water lines.

These Hybrid FPGreen and FPRed turbos sacrificed efficiency in the name of compatibility, while putting guys like Hill, Cokic, Blaha, Brown and others deep into the 10 and even 9 second region. These turbochargers retained the mass produced OEM turbine housing for ease of installation, but were packed with much larger TD06H turbine wheels to satisfy the ever increasing exhaust flow requirements of the high powered DSM. Hacked? Maybe- but they were freakin fast! At least we thought they were fast, but that has all changed now. Now we have FP30s.

What is it?

The heart of the FP30 series turbochargers is the Garrett Ballistic Concepts GT30 cartridge, or CHRA (Center Housing Rotating Assembly). These are great cartridges, full ball bearing design lets them spin in a light breeze. Their low inertia turbine blades contribute to rapid shaft acceleration. The flow capacity and high efficiency of these newly engineered turbine blades is hard to believe for a wheel of its size.

The GT30 turbine wheel is smaller in diameter than the Mitsubishi TD06 and TD06H turbine wheels, but flows far more, allowing greater boost pressure without unfavorably high ratios of exhaust to intake pressure. To put it simply, the intake manifold pressure stays higher than the exhaust manifold pressure under a wider range of operating conditions. This is good.

Having a modern cartridge with ball bearings and super efficient blades isn't going to do anyone any good if it doesn't bolt up. The existing 7cm^2 and 8cm^2 Mitsubishi turbine housings were not only too small for the GT30 turbine wheel, but mass production design compromises such as an offset non-symetric volute and poor material made them very undesirable. It was decided to abandon attempts to force them to work. Design work started on a totally new turbine housing: a truly perfect turbine housing worthy of the GT30 CHRA.

The result of the research is our race inspired totally symetric volute scaled to perfectly match the dimensions of the GT30 turbine wheel. This larger housing incorporates a built in wastegate mount which offers simplified installation without compromising boost control like inferior internal wastegates. Boost pressure can be set as low as 14psi without ANY boost creeping at higher RPM.

Another feature of the housing is the turbine inlet. 60mm diameter, and a surface that is as as smooth as an extrude honed housing throughout the entire volute. The FP30 housing does not require a $95 port job in order for it to perform properly! There has never been a housing like this available to the public.

To avoid a common problem with turbocharger exhaust housings, cracking, the FP30 turbine housing is investment cast in 310 stainless steel for high temperature strength and corrosion resistance. Test units in the field for almost two years showed no cracking or erosion. The FP30 turbine housing casting also offers a weight savings of almost 5 pounds over the OEM Mitsubishi 7cm^2 and 8cm^2 housings.

To further simplify and reduce weight, an F1 style low profile V-band clamp is used for main turbine discharge. V-band clamps are much lighter and quicker to connect than typical 4 and 5 bolt flanges. Kiss that crow foot 14mm wrench goodbye. A single 7/16 nut is all that stands between you and DP removal.

We highly recommend that you call to place your order on this item due to the complexity, expense and options possible with this turbocharger. Selecting next day air shipping and expecting your shiny new turbo to show up tomorrow isnt going to happen. Generally, options and questions regarding setups require several tech sessions between you, the customer, and one of our highly experienced turbo experts.